KornEquipped

2cell_lithium_battery_backup

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:58:42+00:00

20a_rc_speed_control

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:52:17+00:00

50w_led_specs

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:05:47+00:00

Led_50W_5000LM Description: * Voltage: 32-35V * Current: 1500mA * Chip: Genesis's LED 30Mil chip * Luminous Flux: 4500-5000LM * Output Power: 50W * Light Color: White(6000-6500k), Warm White(3000k-3200k) * Beam Angle: 120-140 * Working Life: 50000h

2009_gmc_envoy

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:46:27+00:00

2009 GMC Envoy Build Sheet Engine (LL8) ENGINE,4.2L,DOHC,L,MFI,ALUM, 6 CYL Transmission (M30) Transmission,AT 4-Х SPEED,4L60E,ЭЛЕКТРОН Model_code T,TT15506 RPO Codes: * * 1SZ (PACKAGE OPTION-); * 3SB (PACKAGE SLE OPTION 2);

acs712_modules

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:44:17+00:00

5A Module 20A Module 30A Module 185mV/Amp 100mV/Amp 66mV per Amp Let us assume that the microcontroller you are using has a 10-bit ADC and operates at 5V with a reference voltage of 5V for ADC conversion in that case the microcontroller will read the values of ADC from 0 to 1024.

acs758

Anonymous (anonymous@undisclosed.example.com) — 2026-04-25T21:41:17+00:00

antenna_bulkhead_box

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:12:51+00:00

* 1 - HF trapped EFHW * 2 - 144 J-Pole * 3 - 440 J-Pole * 4 - HF Longwire

arduino_nano

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:09:23+00:00

at_tiny85_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T11:27:38+00:00

at_tiny2313_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T11:27:14+00:00

atmel_initial_fuse_setup

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T11:22:44+00:00

for AT Tiny85 avrdude -v -pattiny85 -cusbasp -Pusb -e -Uefuse:w:0xff:m -Uhfuse:w:0xdf:m -Ulfuse:w:0xe2:m -B3 For ATMega328p avrdude -v -patmega328p -cusbasp -Pusb -e -Ulock:w:0x3F:m -Uefuse:w:0x05:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m -B3

auto_relay_pinouts

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:32:25+00:00

Common Automotive Relay Pinouts

automotive_data_resources

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:09:08+00:00

* OEM SERVICE INFO - * OEM SERVICE INFO - * ALL DATA DIY - * MITCHELL DIY - * MOTOLOGIC - * IDENTIFIX -

avrdude_flashing_commands

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T11:54:08+00:00

To read a file avrdude -v -patmega328p -cusbasp -Pusb -e -U flash:r:flash.bin:r To write a file avrdude -v -patmega328p -cusbasp -Pusb -e -U flash:w:flash.hex:i Set Fuses for AT Tiny85 avrdude -v -pattiny85 -cusbasp -Pusb -e -Uefuse:w:0xff:m -Uhfuse:w:0xdf:m -Ulfuse:w:0xe2:m -B3

cn6009_boost_converter

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:19:25+00:00

CN6009 Step-up Dc Power Converter * * IN-IN + input Positive Input Negative! * Positive output OUT + OUT-output negative * Test comparison sample reference: * Input 3V Output 12V 0.4A 4.8W * Input 5V Output 12V 0.8A 9.6W * Input 7.4V Output 12V 1.5A 18W

dallas_18b20_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-04-25T21:14:05+00:00

db9_db25_adapter

Anonymous (anonymous@undisclosed.example.com) — 2026-02-20T02:58:05+00:00

DB9DB2518233242057667486922

dc_power_connectors

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:26:28+00:00

Available DC CoAxial power Connectors

dds_comparison

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:50:43+00:00

ADF4350/4351 137.5 MHz to 4.4 GHzSI5351a 2.5 kHz to 200 MHzAD9850/9851 60 MhzAD9833/9834 12 MhzAD9910

digispark_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T11:27:50+00:00

epson_tm88_cash_drawer

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:02:30+00:00

esp-01

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:08:57+00:00

esp-12

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T12:58:12+00:00

esp32_devkit_v1_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-06-22T21:15:56+00:00

esp8266_notes

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:54:46+00:00

ESP8266 Pins *ADADC0*D0GPIO16*D1GPIO5SCL*D2GPIO4SDA*D3GPIO0*D4GPIO2TXD1*D5GPIO14SCK*D6GPIO12MISO*D7GPIO13MOSIRXD alt*D8GPIO15SSTXD alt*D9GPIO3RXD*D10GPIO1TXDADC0A0GPIO00D3GPIO01D10TXDGPIO02D4TXD1GPIO03D9RXDGPIO04D2GPIO05D1 GPIO12D6GPIO13D7RXD altGPIO14

fuel_injection_tester

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:52:19+00:00

Product description  Explanation for 4 modes  Mode the tester outputs 1 pulse, whose pulse width is about 250ms Mode the tester outputs 50 pulse, every pulse's pulse width is about 7ms Mode the tester outputs 100 pulse, every pulse's pulse width is about 3.5ms Mode the tester outputs pulse continuously at the rate of 50 pulses per about 1450ms, every pulse's pulse width is about 7ms

futaba_na202md13aa

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:28:57+00:00

Futaba NA202MD13AA VFD I had used a bunch of these back in the day... I purchased yhese Futaba Vacuum Flourescent displays for $4 each. I wanted a winamp display and a unique nameplate for my desk. It comes with a 10 pin connector but 5 of those get grounded 2 for +v5 and three data signals.... Using a pic18f452 to drive it. Also ported it to an pic18f1320 hex file below is for the 18f452 that works with the schematic shown. Also have code for a car warning message panel

hc05_bluetooth_module

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:10:46+00:00

hid_p10_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-04-28T16:35:19+00:00

itsy_bisty_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-05-11T19:48:11+00:00

k40_notes

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:03:39+00:00

K40Lens The Lens itself is 18mm diameter with focal length of 2 inches or 50mm Make sure you place lens flat side down and convex side top. K40Mirrors In a nutshell there 3 most common types of mirrors used in laser cutters: Silicone (Si) with a thing gold layer on top. This mirror is relatively inexpensive and good for lasers up to 80 Watt. It has great reflectance, but hard to clean and can get damaged easily.

led_matrix_power_hack

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T21:29:26+00:00

Simple 1 wire addition will allow easy addition of a Wifi dongle to the RJ11 port. Cable Pinouts: DescDB25DB9RJ11RJ45+5V8146TXD3224RXD2335GND7513

m5_midi

Anonymous (anonymous@undisclosed.example.com) — 2026-02-19T02:22:09+00:00

Port A PinWire ColorDescription1Yellowinput2WhiteOutput (Idles High)3Red+5V4BlackGround

m5_stack

Anonymous (anonymous@undisclosed.example.com) — 2026-02-01T17:12:21+00:00

* *

mini_360_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-04-25T17:12:25+00:00

mini_max232_module

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:53:16+00:00

mono_amp_lpf

Anonymous (anonymous@undisclosed.example.com) — 2026-02-20T13:31:15+00:00

Mono Amp with Low Pass Filter

mt3608_boost_converter

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:22:40+00:00

MT3608 DC-DC Step Up Booster Power Supply Module Description * Electrical characteristics * The maximum output current: 2A * The input voltage: 2V ~ 24V * The maximum output voltage: > 28V * Efficiency: > 93% Mechanical properties Product size: 36 mm * 17 mm * 14 mm

obdii_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:10:22+00:00

pd_power_supply_module

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:50:09+00:00

penny_giles_interface

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:59:50+00:00

seeed_xiao_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-04-25T13:20:13+00:00

smd_reflow_solder_specs

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T22:44:58+00:00

start

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T21:52:34+00:00

The extra tiny Tidbits are here....

stm_pinouts

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T12:46:44+00:00

swipe_reader_wire_colors

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:34:54+00:00

Magtek Serial PinColorUse2Yellowswipe data3Greenpc txd4OrangeVCC5BrownGND Magtek PS2 Pin?ColorKBDCMP4BYellowVCCVCC3BOrangeGNDGND3BBareGNDGND5MBlueNCCLK1MGreenNCDATA1FRedDATANC5FBrownCLKNC IDTech P/S-2 Pin?ColorKBDCMP4BYellowVCCVCC3BBlackGNDGND3BBareGND

tayda_pinouts

Anonymous (anonymous@undisclosed.example.com) — 2026-05-22T19:18:37+00:00

thc-debug

Anonymous (anonymous@undisclosed.example.com) — 2026-04-25T21:43:24+00:00

tm88_config

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:36:00+00:00

tm88_setup

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:00:01+00:00

setup steps #!/bin/sh #install Epson printer TM-88 / TM-20 sudo mkdir /tmp/install cd /tmp/install sudo wget -O /install/master.zip 'https://github.com/plinth666/epsonsimplecups/archive/master.zip' sudo unzip master.zip cd epsonsimplecups-master sudo apt-get update sudo apt-get install libcups2-dev sudo apt-get install libcupsimage2-dev sudo make sudo make install

trailer_wiring

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:37:04+00:00

Stop LampSignal LampTrailer LampOffOffOffOnOffOnOffOnOnOnOnOff

usb_boost_converter

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:25:54+00:00

DC - DC booster module (0.9 V to 5 V) 5 V 600 ma USB mobile booster * Input voltage: 0.9V-5V DC * Transfer efficiency:96%(max) * With USB port * With working indicator light * with one AA battery power supply output current can up to 200~300mA,

usb_pinouts

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:01:53+00:00

using_depreciated_ssh_keys

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:33:47+00:00

% cat /etc/ssh/ssh_config Host * SendEnv LANG LC_* IdentityFile ~/.ssh/id_rsa IdentitiesOnly yes HostkeyAlgorithms +ssh-rsa PubkeyAcceptedAlgorithms +ssh-rsa

vi_tips

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T00:38:40+00:00

To change all uppercase letters to lowercase in vi, you can use the command :%s/.*/\L&/ To insert a quote at the beginning of each line :%s/^/“/ To insert a quote and comma at the end of each line :%s/$/“,/ Find non ASCII Characters grep --color='auto' -P "[\x80-\xFF]" grep -P -n "[\x00-\x1F\x7F-\xFF]" input_file grep --color='auto' -P -n '[^\x00-\x7F]' grep --color='auto' -P -n "[^[:ascii:]]"

w1209_temperature_controller

Anonymous (anonymous@undisclosed.example.com) — 2026-01-30T23:14:10+00:00

xbox_360_rf_module_pinout

Anonymous (anonymous@undisclosed.example.com) — 2026-01-31T18:58:22+00:00